The TA330 is a detector intended to allow a technician to detect the presence of the keyless entry carrier frequency in the range 125 to 140 kHz (as used by most manufacturers). The device has a short range by design, allowing the technician to check each pickup coil in turn and hence identify a faulty unit. The detector does not pick up or de..

The TA487 is an interface that allows industry-standard IEPE (integrated electronic piezoelectric) sensors to be used with any oscilloscope or data acquisition device with BNC inputs. The device is powered from any USB port, using the cable supplied, and provides a 4mA constant current source to power a connected IEPE sensor. A TA095 IEPE a..

Convert your oscilloscope accessories with 4mm adaptor to BNC connection. The BNC to 4mm adaptor connects two 4mm (banana) plugs to a BNC socket. The 4mm sockets and BNC plug are fully shrouded for safety...

Set of two Pomona adjustable piercing probes The TA007 Insulation Piercing Test Clip set is ideally suited for automotive test and diagnosis. The piercing clips allow the user to provide the exact pressure needed to pierce the insulation of a wide range of wire types and sizes. The clips also feature a rotating banana jack that prevents the test..

This high-quality general purpose oscilloscope probe has a 60 MHz bandwidth. A two-position slide switch allows attenuation of either x1 or x10 to be selected. This probe is particularly useful if you want to probe higher speed automotive CAN bus and FlexRay signals using the Pico oscilloscope...

Do you need to measure the current through a circuit but can’t find anywhere on the vehicle where you can connect your current clamp? Fuse extension leads are a simple accessory that can save you valuable time. Fuse extension leads are quick and easy to use: simply remove the fuse (of the circuit you wish to test) from your fusebox and ..

  J Case fuse extension lead The TA168 JCASE fuse extension lead is designed to be used with standard and low profile JCASE fuses. JCASE is a cartridge style fuse with female terminal design, providing both increased time delay and low voltage drop to protect high current circuits & handle inrush currents.  ..

Do you need to measure the current through a circuit but can’t find anywhere on the vehicle where you can connect your current clamp? Fuse extension leads are a simple accessory that can save you valuable time. Fuse extension leads are quick and easy to use: simply remove the fuse (of the circuit you wish to test) from your fusebox and ..

Do you need to measure the current through a circuit but can’t find anywhere on the vehicle where you can connect your current clamp? Fuse extension leads are a simple accessory that can save you valuable time. Fuse extension leads are quick and easy to use: simply remove the fuse (of the circuit you wish to test) from your fusebox and ..

The TA206 maxi fuse extension lead is designed to be used with standard maxi automotive fuses. The maxi fuse is a large blade-style fuse used to protect high-current circuits and handle large inrush currents on some vehicles...

With high bandwidth and fault protection, the 10:1 attenuator allows you to measure fuel injector and primary ignition waveforms using PicoScope oscilloscopes. The TA197 is a passive 10:1 attenuator. This means that, for example, a 10 V signal at its input appears as a 1 V signal on its output. It allows voltages of up to 400..

This kit is available in either black or red and contains all the commonly used Pico automotive test probes. Each kit contains: 2 x multimeter test probes 2 x small crocodile clips 2 x shrouded to unshrouded adaptors 2 x battery clips 2 x flexible back-pinning probes 1 x single dolphin clip. This kit is similar to the set of red probe..

This kit is available in either black or red and contains all the commonly used Pico automotive test probes. Each kit contains: 2 x multimeter test probes 2 x small crocodile clips 2 x shrouded to unshrouded adaptors 2 x battery clips 2 x flexible back-pinning probes 1 x single dolphin clip. This kit is similar to the set of red probe..

The multimeter probes offer a quick and easy solution, where a permanent connection is not required. The 4 mm socket in the handle of the probe connects straight into one of our premium test leads. Length: 115 mm Diameter: 20 mm..

The multimeter probes offer a quick and easy solution, where a permanent connection is not required. The 4 mm socket in the handle of the probe connects straight into one of our premium test leads. Length: 115 mm Diameter: 20 mm..