Pico Technology

Grid View:

P4225 Pico 2 channel Automotive Oscilloscope - Scope only

$1,318.30 $1,373.30

P4225 - Pico Automotive oscilloscope 2 channel. Scope only..

P4425 Pico BNC 4 channel oscilloscope - Scope Only

$2,033.90 $2,181.80

P4425 Pico Automotive 4 channel oscilloscope - Scope only..

Pico Mixmaster kit

$667.59

12 Channel automotive secondary ignition signal mixer. With the Mixmaster 12–channel automotive signal mixer you can view an ignition parade display of up to 12 cylinders on any lab scope...

Pico NVH Diagnostics Kit 3ch

$1,033.73

Pico Technology 3 channel Noise Vibration and Harshness diagnostic kit. Important note: The NVH kit from Pico Technology only works with Pico Automotive Oscilloscopes, and requires an unlock code in order to allow your PicoScope to work with the NVH software. This unlock key is limited to one PicoScope Automotive scope and is not trans..

Pico NVH Diagnostics Kit 4ch

$1,738.00

Pico Technology 4 channel Noise Vibration and Harshness diagnostic kit. Important note: The NVH kit from Pico Technology only works with Pico Automotive Oscilloscopes, and requires an unlock code in order to allow your PicoScope to work with the NVH software. This unlock key is limited to one PicoScope Automotive scope and is not trans..

Optical Sensor Kit - NVH accessory

$634.10

This kit is a companion to our NVH kits, providing a high-quality optical sensor and magnetic mount for use with our balancing software. Primarily used for balancing of propshafts (drive shafts), this kit also supports frequency measurement of other rotating items. When used with PicoDiagnostics balancing software, a simple graphical guide al..

Microphone - Pico NVH accessory

$126.83

The TA144 is the standard Pico microphone for use with Pico's NVH Interface...

Single Mounting Magnet for NVH accelerometer

$84.21

Mounting magnet for NVH kit accelerometer..

PP939 - Pico WPS Pressure Transducer Master Kit

$1,693.12

Pico Tech Pressure Transducer - WPS 500x kit With the uncompromising resolution and accuracy of the WPS500X Automotive Pressure Transducer you can perform quick and accurate pressure analysis of many automotive systems. The WPS500X features an extremely fast 100 µs response rate from 0% to 90% of full scale and sensitivity down to about..

PQ071 Pico Fuel Sight Block kit

$337.26

The Pico PQ071 Fuel sight block kit is an accessory for the Pico WPS500 pressure transducer kit. The Sight block kit contains the sight block, a stop valve for testing a negative pressure fuel pump under load, and 3 sets of hose barbs for connecting to different size fuel hoses. The kit is intended for diagnosing problems with low-pressure..

TA323 Pico Diesel Glow Plug Adaptor kit

$586.30 $634.10

The TA323 is an accessory kit to be used in conjunction with the WPS500x Pressure transducer and Pico automotive pc based oscilloscope (both sold separately). Add diesel compression testing to your list of uses with this glow plug adaptor kit. It contains 15 different glow plug adaptors and the adaptor that connects them to our standard univers..

PP833 WPS600c Pressure Transducer

$1,505.90

With high accuracy and a wide measuring range, the WPS600C Hydraulic Pressure Transducer connects to your PicoScope for convenient analysis and diagnosis of pressurized systems. Accurately measure up to 600 bar (8700 psi) Ultra-fast 100 microsecond response time (0% to 90% of full scale) Internal rechargeable LiPo battery Industry-stand..

Pico 0-2000 BNC Amp Current Clamp

$407.00 $452.10

The 200 A / 2000 A current clamp with BNC connector allows you to measure up to 2000 amps without cutting, or disconnecting or stripping wires. Simply clamp the jaws around the cable to be tested and plug the clamp into your PicoScope. Before the launch of this probe we recommended the TA019 (600 A) for working on the starting and..

Pico BNC 0-30 Amp Current Clamp

$397.87

The TA234 probe is a 30 A current clamp with BNC adaptor. The extended measuring jaws allow measurement in a confined space. When measuring DC, a simple thumbwheel on the probe allows zero adjustment. This current clamp is ideally suited for use with PicoScope oscilloscopes and features additional screening to reduce noise pickup. ..

Pico BNC 0-60 Amp Current Clamp

$296.84

The TA018 current clamp with BNC adaptor is ideal for use with PicoScope automotive oscilloscopes for measuring currents between 10 mA and 60 A. This enables the PicoScope to display current waveforms for fuel injectors and fuel pumps. The current clamp has two calibration settings, set by a slider switch on the handle of the probe. 1 mV/1..

Showing 31 to 45 of 89 (6 Pages)