The TA019 current clamp with BNC connector is ideal for use with a PicoScope automotive oscilloscope to display starter current waveforms, charging currents and for performing quick compression tests. The current clamp can measure up to 600 A (AC or DC). In use there is no need to break into the circuit or disturb the isolation as the ..
Flexible Coil on plug inductive probe including BNC to BNC lead with ground The PP357 coil-on-plug (COP) and signal probe from Pico Technology is the fastest way to check coil-on-plug ignition coils and spark plugs. Find misfires fast Displays scope patterns of the secondary, faster than scoping the primary Works on all automotive scop..
You’ve got the best oscilloscope, now get the best leads These premium leads are colour–coded so that the colour of the lead in the engine bay matches the colour of the on–screen waveform in PicoScope Automotive — never again will you waste your time wondering which lead is what. Our premium leads are fully s..
Coil on Plug extension lead Set of 4. Coil-on-Plug extension leads are the simple accessory that allow you to take accurate secondary ignition measurements on Coil-on-Plug ignition systems. Coil-on-Plug extension leads are designed to aid diagnostics on secondary ignition circuits by allowing an HT measurement to be made when there ..
Coil on plug extension lead (Single) Coil-on-Plug extension leads are the simple accessory that allow you to take accurate secondary ignition measurements on Coil-on-Plug ignition systems. Coil-on-Plug extension leads are designed to aid diagnostics on secondary ignition circuits by allowing an HT measurement to be made when there i..
Pico Secondary ignition pickup lead - capacitive with BNC (MI074) Due to the high voltages involved in secondary ignition systems, it is not possible to make measurements by direct connection. Attempting to make a direct connection will almost certainly damage the measuring instrument. The MI074 is a capacitive pickup that simply connects aro..
Pico Technology Ultrasonic Parking Sensor Detector (***To be used as an accessory with Pico automotive oscilloscope. Pico automotive oscilloscope supplied separately.***) This 2 meter long lead and detector is intended to allow a technician to prove the correct operation of each of the ultrasonic parking sensors in turn. By directly showing the ..
The TA330 is a detector intended to allow a technician to detect the presence of the keyless entry carrier frequency in the range 125 to 140 kHz (as used by most manufacturers). The device has a short range by design, allowing the technician to check each pickup coil in turn and hence identify a faulty unit. The detector does not pick up or de..
Set of two Pomona adjustable piercing probes The TA007 Insulation Piercing Test Clip set is ideally suited for automotive test and diagnosis. The piercing clips allow the user to provide the exact pressure needed to pierce the insulation of a wide range of wire types and sizes. The clips also feature a rotating banana jack that prevents the test..
This high-quality general purpose oscilloscope probe has a 60 MHz bandwidth. A two-position slide switch allows attenuation of either x1 or x10 to be selected. This probe is particularly useful if you want to probe higher speed automotive CAN bus and FlexRay signals using the Pico oscilloscope...
This kit contains 11 sets of 6 different sized universal breakout leads and a set of 6 back pinning probes. The breakout leads come with 7 different sized flat blade connectors (0.6 mm, 1.2 mm, 2.0 mm, 2.3 mm, 2.8 mm, 4.8 mm and 6.0 mm), and 4 different round pin sizes (1.5 mm, 2.0 mm, 3.5 mm and 4.0 mm). The individual breakout leads are design..
Pico’s universal 6-way breakout leads eliminate the need to own many specific breakout leads for engine diagnostics. The breakout leads are available with four different sizes of connectors allowing you to connect to virtually any sensor in the engine compartment—of any vehicle—using just four leads. Never again will you need to s..
Do you need to measure the current through a circuit but can’t find anywhere on the vehicle where you can connect your current clamp? Fuse extension leads are a simple accessory that can save you valuable time. Fuse extension leads are quick and easy to use: simply remove the fuse (of the circuit you wish to test) from your fusebox and ..