These connector breakout leads enable voltage readings to be taken from the numerous sensors and actuators in the engine compartment. The required connector breakout lead is simply connected into the existing cable loom, and the output signal can then be taken from the 4 mm banana plugs into the automotive oscilloscope using TA1..

Pico connector breakout leads enable you to take voltage readings from the numerous sensors and actuators in the engine compartment. Simply connect the breakout lead into the existing cable loom, and then take the output signal from the 4 mm banana plugs into the automotive oscilloscope using one of the TA125 to TA128 premium te..

This connector breakout lead enables you to take voltage readings from the numerous sensors and actuators in the engine compartment. Simply connect the breakout lead into the existing cable loom, and then take the output signal from the 4 mm banana plugs into the automotive oscilloscope using one of the TA125 to TA128 premium test leads. ..

Passive oscilloscope probe: 100MHz bandwidth 1:1/10:1 switchable, BNC This high-quality general purpose oscilloscope probe has a 100 MHz bandwidth. A two-position slide switch allows attenuation of either x1 or x10 to be selected. This probe is particularly useful if you want to probe CAN bus and FlexRay signals. This probe has replac..

You’ve got the best oscilloscope, now get the best leads Our Pico premium leads are color-coded so that the color of the lead in the engine bay matches the color of the on-screen waveform in PicoScope Automotive – never again will you waste your time wondering which lead is which. Our Pico premium leads are fully s..

The TA144 is the standard Pico microphone for use with Pico's NVH Interface...

Mounting magnet for NVH kit accelerometer..

Pico Tech Pressure Transducer - WPS 500x kit With the uncompromising resolution and accuracy of the WPS500X Automotive Pressure Transducer you can perform quick and accurate pressure analysis of many automotive systems. The WPS500X features an extremely fast 100 µs response rate from 0% to 90% of full scale and sensitivity down to about..

With the inclusion of a dual WPS600 hydraulic transducer kit, the Off-Highway Elite kit gives technicians working with off-highway equipment and heavy-duty vehicles the tools to diagnose faults in hydraulic systems, in addition to the vehicle and equipment components and systems covered by the Off-Highway Expert kit. The Off-Highway Elite kit provi..

The TA323 is an accessory kit to be used in conjunction with the WPS500x Pressure transducer and Pico automotive pc based oscilloscope (both sold separately). Add diesel compression testing to your list of uses with this glow plug adaptor kit. It contains 15 different glow plug adaptors and the adaptor that connects them to our standard universa..

With high accuracy and a wide measuring range, the WPS600C Hydraulic Pressure Transducer connects to your PicoScope for convenient analysis and diagnosis of pressurized systems. Accurately measure up to 600 bar (8700 psi) Ultra-fast 100 microsecond response time (0% to 90% of full scale) Internal rechargeable LiPo battery Industry-stand..

The 200 A / 2000 A current clamp with BNC connector allows you to measure up to 2000 amps without cutting, or disconnecting or stripping wires. Simply clamp the jaws around the cable to be tested and plug the clamp into your PicoScope. Before the launch of this probe we recommended the TA019 (600 A) for working on the starting and..

The TA018 current clamp with BNC adaptor is ideal for use with PicoScope automotive oscilloscopes for measuring currents between 10 mA and 60 A. This enables the PicoScope to display current waveforms for fuel injectors and fuel pumps. The current clamp has two calibration settings, set by a slider switch on the handle of the probe. 1 mV/10 m..

The TA019 current clamp with BNC connector is ideal for use with a PicoScope automotive oscilloscope to display starter current waveforms, charging currents and for performing quick compression tests. The current clamp can measure up to 600 A (AC or DC). In use there is no need to break into the circuit or disturb the isolation as the ..

Flexible Coil on plug inductive probe including BNC to BNC lead with ground The PP357 coil-on-plug (COP) and signal probe from Pico Technology is the fastest way to check coil-on-plug ignition coils and spark plugs. Find misfires fast Displays scope patterns of the secondary, faster than scoping the primary Works on all automotive scop..