You’ve got the best oscilloscope, now get the best leads These premium leads are colour–coded so that the colour of the lead in the engine bay matches the colour of the on–screen waveform in PicoScope Automotive — never again will you waste your time wondering which lead is what. Our premium leads are fully s..

The 30 A precision current clamp with BNC connection allows you to measure from 5 mA up to 30 A without cutting, disconnecting or stripping the wire. It is ideal for measuring the currents in sensors and actuators across most modern passenger and commercial vehicles. The TA189 provides improved sensitivity, lower noise and faster response. Featu..

The PicoBNC+® equipped TA496 is a natural choice if you are a PicoScope 4225A and 4425A user looking to add a compact low amps clamp to your PicoScope probe collection. The PicoBNC+® 60 A DC compact current clamp’s reduced form factor fits comfortably in your hand and improves accessibility in tight and difficult to access test loc..

Coil on Plug extension lead Set of 4. Coil-on-Plug extension leads are the simple accessory that allow you to take accurate secondary ignition measurements on Coil-on-Plug ignition systems. Coil-on-Plug extension leads are designed to aid diagnostics on secondary ignition circuits by allowing an HT measurement to be made when there ..

Coil on plug extension lead (Single) Coil-on-Plug extension leads are the simple accessory that allow you to take accurate secondary ignition measurements on Coil-on-Plug ignition systems. Coil-on-Plug extension leads are designed to aid diagnostics on secondary ignition circuits by allowing an HT measurement to be made when there i..

Pico Secondary ignition pickup lead - capacitive with BNC (MI074) Due to the high voltages involved in secondary ignition systems, it is not possible to make measurements by direct connection. Attempting to make a direct connection will almost certainly damage the measuring instrument. The MI074 is a capacitive pickup that simply connects aro..

The TA408 is a high-end current clamp designed for the most demanding Vehicle Manufacturer requirements. This 100 A current probe is based on closed-loop technology, is powered directly from the scope, and has a built-in power on zero function so no buttons are required. It is designed for battery drain applications and features excellent resolu..

2 x WPS600c in carry case. With high accuracy and a wide measuring range, the WPS600C Hydraulic Pressure Transducer connects to your PicoScope for convenient analysis and diagnosis of pressurized systems. Accurately measure up to 600 bar (8700 psi) Ultra-fast 100 microsecond response time (0% to 90% of full scale) Internal rechargeable..

Traditional pressure gauges do not provide technicians with a graphical representation of their measurements so they can’t show and/or record the pressure values and trends they observe during the test. As such, they can’t easily share their results with customers, colleagues or technical support and warranty teams. Nor can they come ba..

Pico Technology Ultrasonic Parking Sensor Detector (***To be used as an accessory with Pico automotive oscilloscope. Pico automotive oscilloscope supplied separately.***) This 2 meter long lead and detector is intended to allow a technician to prove the correct operation of each of the ultrasonic parking sensors in turn. By directly showing the ..

The TA330 is a detector intended to allow a technician to detect the presence of the keyless entry carrier frequency in the range 125 to 140 kHz (as used by most manufacturers). The device has a short range by design, allowing the technician to check each pickup coil in turn and hence identify a faulty unit. The detector does not pick up or de..

The TA466 is a standalone tester that is used to check for the presence or absence of a voltage, and thereby allows the technician to confirm that the high-voltage has been disconnected from a circuit before proceeding. The measurement range is up to 690 V AC and 950 V DC to suit electric and hybrid vehicles, and the unit features a 3-digit red and..

The TA467 Insulation tester is specially designed for vehicles with on-board high voltages and conforms to EN61010 CAT III (1000 volts) and CAT IV (600 volts). The insulation test function allows testing of the insulation of the high voltage wires found on high-voltage vehicles. It can be used as a stand-alone device or linked wirelessly with the s..

The TA487 is an interface that allows industry-standard IEPE (integrated electronic piezoelectric) sensors to be used with any oscilloscope or data acquisition device with BNC inputs. The device is powered from any USB port, using the cable supplied, and provides a 4mA constant current source to power a connected IEPE sensor. A TA095 IEPE a..

Field repairable back pinning and piercing probe set, with very small diameter, very sharp pins. ..