Search - pico

The 200 A / 2000 A current clamp with BNC connector allows you to measure up to 2000 amps without cutting, or disconnecting or stripping wires. Simply clamp the jaws around the cable to be tested and plug the clamp into your PicoScope. Before the launch of this probe we recommended the TA019 (600 A) for working on the starting and..

The TA018 current clamp with BNC adaptor is ideal for use with PicoScope automotive oscilloscopes for measuring currents between 10 mA and 60 A. This enables the PicoScope to display current waveforms for fuel injectors and fuel pumps. The current clamp has two calibration settings, set by a slider switch on the handle of the probe. 1 mV/10 m..

The TA019 current clamp with BNC connector is ideal for use with a PicoScope automotive oscilloscope to display starter current waveforms, charging currents and for performing quick compression tests. The current clamp can measure up to 600 A (AC or DC). In use there is no need to break into the circuit or disturb the isolation as the ..

The PicoBNC+ NVH Accelerometer significantly enhances NVH testing by capturing triaxial data—fore-aft, lateral, and vertical—through a single PicoScope channel. Capable of measuring up to ±5 g with a frequency response from DC to 350 Hz, the triaxial design of the accelerometer eliminates the need for manual connection and config..

The PicoBNC+ NVH Microphone is a compact tool specifically engineered for accurate noise, vibration, and harshness diagnostics. Covering a wide 20 Hz to 20 kHz audible range, it offers a lower noise floor and improved measurement repeatability for accurate fault finding during NVH testing, including automotive, marine, commercial, agriculture, cons..

Flexible Coil on plug inductive probe including BNC to BNC lead with ground The PP357 coil-on-plug (COP) and signal probe from Pico Technology is the fastest way to check coil-on-plug ignition coils and spark plugs. Find misfires fast Displays scope patterns of the secondary, faster than scoping the primary Works on all automotive scop..

The 30 A precision current clamp with BNC connection allows you to measure from 5 mA up to 30 A without cutting, disconnecting or stripping the wire. It is ideal for measuring the currents in sensors and actuators across most modern passenger and commercial vehicles. The TA189 provides improved sensitivity, lower noise and faster response. Featu..

The PicoBNC+® equipped TA496 is a natural choice if you are a PicoScope 4225A and 4425A user looking to add a compact low amps clamp to your PicoScope probe collection. The PicoBNC+® 60 A DC compact current clamp’s reduced form factor fits comfortably in your hand and improves accessibility in tight and difficult to access test loc..

The PicoBNC+ Extension Cable provides the extra reach required for large-scale diagnostic scenarios. Measuring 3 meters in length, this robust cable gives technicians additional flexibility while performing tests at the rear of the vehicle, under the chassis, or deep within the engine bay.  Designed specifically for the next generation of..

Coil on Plug extension lead Set of 4. Coil-on-Plug extension leads are the simple accessory that allow you to take accurate secondary ignition measurements on Coil-on-Plug ignition systems. Coil-on-Plug extension leads are designed to aid diagnostics on secondary ignition circuits by allowing an HT measurement to be made when there ..

Precision NVH diagnostics begin with a secure connection. The TA096 Mounting Magnet is engineered to provide a high-strength, stable interface between your accelerometer and the vehicle under test. By ensuring a rigid bond to any ferrous surface, the TA096 eliminates "sensor bounce" and ensures that the data on your screen accurately refl..

Coil on plug extension lead (Single) Coil-on-Plug extension leads are the simple accessory that allow you to take accurate secondary ignition measurements on Coil-on-Plug ignition systems. Coil-on-Plug extension leads are designed to aid diagnostics on secondary ignition circuits by allowing an HT measurement to be made when there i..

Pico Secondary ignition pickup lead - capacitive with BNC (MI074) Due to the high voltages involved in secondary ignition systems, it is not possible to make measurements by direct connection. Attempting to make a direct connection will almost certainly damage the measuring instrument. The MI074 is a capacitive pickup that simply connects aro..

Pico USB 2.0 4.5m ..

Pico USB 3.0 Lead 1.8m..